How to Install the Quick-Release Push-Button Lock for the Window Guard

Attach typically the Strike Pin to the window guard

Typically the Strike Pin (3) should be permanently installed on or around the outer alloy framing in the windowpane guard -referred to be able to from now upon as WG- on the side of the WG’s “door” opposite involving the hinge, near the middle (the same place where a doorknob is positioned on a door). It should extend to the outside from the WOHNGRUPPE toward the wall, so that that will later slide into the Secure Box tip-first when closed.

IMPORTANT: The particular Strike Pin should point straight as you possibly can, ie not directed slightly up, straight down, to the remaining, or to the right. The straighter it really is, the smoother the operation later.

The back of the Strike Pin has strings to get a 1/4″ sl?, so a common way of attaching the strike pin to your WOHNGEMEINSCHAFT is by first affixing a 1/4″ bolt it, then screwing the Strike Pin into that. Even now, you don’t want individuals to be able to simply unscrew the bolt coming from the outside, so it is important that an individual permanently repair it to the WG. It is most often completed by spot welding the attached Strike Pin in place, although if a welder isn’t handy, any way the bolt could be made unturnable will work, such as using one-way bolts.

Attach the Window Safeguard

If this isn’t currently, it’s time to be able to mount the WOHNGRUPPE on your home window. Attach the Secure Box (1) to the end of the pin so of which it locks in position. If it is just not, make sure it is usually unlocked first by pushing the finish regarding the Push Rod (2) into typically the smaller hole of the Lock Box first. This Lock Container will be mounted to the outside wall of your current building, therefore you will need to install the WG in a new position the location where the Secure Box can be installed using the top and bottom screw holes, and may not be pryed off (such as when this sits off the particular edge of any window frame).

Another thing to keep throughout mind this is that will there will end up being an approximately 1/2″ hole drilled by way of your wall positioned in the center of the Fastener Box, and the particular inside of the building, a just one 5/8″ diameter Flange will mount to the wall all-around that hole. So when you put up the WG, you want the Lock Box to become near to the window beginning, but far enough enabling this 1/2″ hole to become drilled from the wall structure, and hopefully get clear of virtually any inner wall items in the way (like inside framing) for a a single 5/8″ diameter around the hole center.

Mark your hole

With the Affect Pin attached to be able to your WG, in addition to the WG linked to your constructing, the others is relatively very simple!

Now we will need to mark the location where the hole will be drilled through the wall so that it suits the small pit on the again of the Lock Box. First, push the Push Rod (2) in the Locking mechanism Box hole thus it releases from your Strike Pin, and remove it. Place the Cardboard Slip (4) all the way onto the Strike Pin number, and cut off the end with a new knife so the cardboard only barely extends beyond the Strike Pin. Close the WG door slowly until the group of friends of cardboard fulfills the wall, and then use a pen to draw a new circle where it lands.

Drill

Officially a 3/8″ drill down bit will get big enough for typically the Push Rod to be able to fit into, yet I recommend a new 1/2″ bit, which leaves more room for error, in addition to is covered upward just fine. Making use of the circle you simply marked, drill a hole straight via your building wall structure until you infringement the other side.

At this specific point, reattach typically the Lock Box to the WG and maintain it closed. An individual from the within should be able to put their own eye through the recently drilled hole and even see the OVERALL small hole regarding the Lock Box. If it will be partially covered, exercise out your hole until there are a clear path to it.

Install the Lock Field

If it is not already, reattach the particular Lock Box for the WG and carry it closed. Tag the upper and even lower holes regarding the Lock Package with your reliable pencil, then open the WG in addition to drill them using the drill bit (NOT the big one! ) of which matches the screws you’re going to be able to use to support the Lock Container, which don’t include the kit. These screws should always be between 1/4″ plus 3/8″, and have to be about 2″ to 3″ lengthy.

With your two holes drilled previously mentioned and below your BIG one, remove the Lock Box from the WG (you know how by now, right? ), place it on the wall structure, and mount it with your many of the. Screw them in until they’re tight, but do not completely fasten just yet.

Align the particular Lock Box

Gradually close the WOHNGRUPPE female mounted Secure Box, being careful To not lock this in place. What’s that? You say the particular Strike Pin is not lining up? Require a chill pill, Now i’m getting there.

push button enclosure Along with your hammer, smack the particular Lock Box sufficient to move that inside the direction it needs to go. If it won’t move, you screwed this in a little too tight and even will need to loosen it. Whenever it is arranged properly, you may possibly lock it within place to assure this works. It can be unlocked, of course, by adhering the Push Fly fishing rod (2) through the particular hole in the wall until it releases. Note that you may have to “fish” around to the smaller hole in the Lock Box to push it in almost all the way.

Whenever everything is layered up, tighten the Lock Box screws all the method. If everything is definitely well aligned, typically the Push Rod need to easily open the WG as well as the WOHNGEMEINSCHAFT should easily lock in place. Despite the screws are usually tightened, you may well be capable to employ the hammer intended for final adjustments.

Leave a reply

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>